F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller
F4 1-2S AIO Brushless Flight Controller

F4 1-2S AIO Brushless Flight Controller

Sale price $39.99 USD Save $0.00 USD
-181 in stock

This AIO F4 FC is suitable for a lighter 1-2S whoop drone perfectly, like Beta65 Pro 2 or Beta75 Pro 2 etc. It integrated with a Betaflight F411 processor FC, Betaflight OSD, SPI Frsky receiver and 1-2S 5A ESC. So the 2S drone could save many weight for a faster fly experience.

F4 2S AIO Brushless Flight Controller

This FC is available for 1S whoop drone also. You need to solder JST-PH 2.0 Cable in wires solder pad to replace the initial power cable. At the same time, you need to use higher than 12000KV motors, such as 0802 17500KV / 19500KV Motors to provide more power.

    SPECIFICATIONS OF FC

    • CPU: STM32F411CEU6 (100MHZ )
    • Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
    • Size: 26mm x 26mm, fully compatible with the all whoop drone mounting pattern, recommend the Beta65X frame and Beta75 Pro frame.
    • Firmware version: betaflight_matekf411rx_4.0.0 (Development Version)
    • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
    • Built in SPI Frsky D16 protocol native receiver, compatible with almost ALL Frsky FCC radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module. Not compatible with Frsky LBT protocol.
    • Power Cable: 55mm, with 2pcs JST-PH 2.0 connector, AKA PowerWhoop connector
    • Weight: 4.5g 

    DIAGRAM FOR F4 2S AIO FC (BUILT-IN FRSKY RX)

         

      SPECIFICATIONS OF ESC

      • Built-in ESC with 5A continuous and peak 6A current
      • Power supply: 1-2S
      • Support BLHeliSuite programmable
      • Factory firmware: S_H_50_REV16_7.HEX
      • Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

      Status LED

      There are 3 LEDs on the bottom of the board to indicate the status, including Receiver LED ( Green), FC Status LED ( Red ) and FC Power LED ( Blue ). 

      LED

      Status

      Description

      Receiver LED ( Green)

      Solid

      Connected or in bind mode

      Receiver LED ( Green)

      Flashing

      Not connected

      Power LED ( Blue )

      Solid

      Power on

      Status LED ( Red )

      Solid

      Motor Armed

      SPI Frsky Receiver

      Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. Pay attention, this is a SPI connection receiver. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.

      The Frsky D16 unstable connection issue is totally resolved since Betaflight 3.4.1. Nowadays, the default configuration from factory is Frsky D16 mode (FRSKY_X).

      Note: If you are using EU-LBT firmware radio controller, you might find that you can't bind successfully to this SPI Frsky receiver. Here are the solutions we provide for you. Thanks to Sebastian Abramowski for giving us the important feedback about binding to EU-LBT firmware radio controller. 

      Binding Procedure

      The binding procedure is reversed as usual. No need to click the bind button when power on.

      • Power on the board, either by connecting the battery or USB power. Then the green receiver LED start to flash.
      • The second step, click the bind button for 3s. Then the green receiver LED will be solid on. This means that the receiver is in bind mode and you could start to bind your radio transmitter.

      For detail procedure of binding, please check the SPI Frsky Receiver Binding Manual.

      Note: This FC board could support the SPI Futaba protocol with this firmware.

      Some pilots would complaint that it is definitely not a long range FC. It looses signal with my transmitter far too often and for what appears to be no reason. This issue is often caused by the location of the antenna. You should keep the antenna away from the FC board to get a stronger signal. For example, run the singal upwards. Thanks for Harley Finberg's advice.

      CLI DUMP of F4 2S Brushless FC

      You can get the Cli dump of F4 AIO 2S Brushless FC here on the BETAFPV Support Freshdesk.

      DIAGRAM FOR F4 2S AIO FC (NO RX)

       

      HOW TO CONNECT THE EXTERNAL RX TO THE FC

      For detailed information of other external receivers, please find out in our support page.

      FAQ

      1. Can this FC used on the Beta75X with 1103 motors?

      Yes, we have tested this FC board with 1103 motors on Beta75X. It performance very well and almost no wash-out issue then. So if you already have a Beta75X, you could just take this AIO FC to replace the stock FC&ESC stack.

      Note: because of the built-in ESC and Frsky receiver, you will lose some remote range and little bit power on Beta75X with this AIO FC.

      2. About the alarm buzzer and LED port?

      No alarm buzzer is supported on this FC board. Programable LED is supported.

        RECOMMENDED PARTS LIST

        PACKAGE

        • 1 * F4 2S brushless flight controller
        • 4 * M1.2x4mm screws
        • 4 * M1.4x5mm screws
        • 4 * Anti-vibration ruber dampers

          Betafpv.com offers a (30) day manufacture defect warranty, starting from the date the product(s) was delivered to the customer. If more than 30 days have passed since receiving your purchase, unfortunately we can’t offer you a refund or exchange.

          For merchandise was confirmed as genuinely defective(Product Design problem & Quality issues), we will ship out a replacement free of charge directly. The consumer will not be charged any fees for approved warranty service.

          In almost all cases, we will work with you to debug your issue firstly. 

          Each claim should have all proof of defect by mean of photo or video showing clearly the defect of the product. Please create a ticket to send us photos or video of your product, a detailed description of your issue, and a description of what you have already done to fix it. We are happy to solve any problem you may meet.

          NOTE: The refund amount is limited to the purchase price of the item.

          Directly Send Ticket: Create a new ticket

          *We do not accept ALL kinds of returns.

          *All sales are final.

          All orders will be processed within 2 business days of your payment clearing. Orders are not shipped or delivered on weekends or holidays. If we are experiencing a high volume of orders or some products out of stock, shipments may be delayed by a few days. Please allow additional days in transit for delivery. If there will be a significant delay in shipment of your order, we will contact you via email.
          Shipping Methods and Charges
          Betafpv.com is currently able to ship orders to most international addresses. All of the parcels are shipped by air. In addition, some countries are not available to ship battery only without purchasing of whoop drone(Logistics company restrictions).
          Two shipping methods are provided for you now. 
          • Standard Shipping
          • Expedited Shipping (DHL)
          If you choose expedited shipping, you need to pay weight-based rates, which will be calculated automatically. If your choose standard shipping, then the shipping fee depends on the value of your orders. If you order is less than 50USD, you have to pay 5 USD for shipping fee. Free shipping is offered if your order is over 50USD.
          Note: Some remote country will be charged shipping fees according to the quotation of logistics company.

          Countries & Area That Can't Be Shipped Battery Without Purchasing of Whoop Drone
          We can't ship the battery to the following countries and areas: Indonesia, South Africa, Philippines, Middle East, South America, Sweden, Israel, Alaska, and US affiliated islands (Hawaii Puerto Rico)
          How To Track My Parcel

          We provide trackable shipping service to most of the package. Please click here to reach detail information.

          Wrong Address

          Shipments will be sent to the address entered on our web page during checkout. We cannot be held responsible if the incorrect shipping address is entered by the customer during checkout. We can only modify a wrong address if customer contacts us before the package is marked as shipped.

          We cannot change shipping addresses after the order has been shipped, as the address information you enter is used as part of the fraud checks and fraud prevention. If additional fees are required to re-ship packages due to address errors, those fees may be passed on to the customer.

          Packages that are returned because of an incorrect address provided by the customer will be subject to an additional shipping charge. This shipping charge will apply even if you were not originally charged shipping under a free shipping promotion. 

          Damaged Box or Incorrect Item(s)

          If you receive damaged or incorrect item(s), contact Customer Support no later than 5 business days of receipt of your shipment to make the necessary corrections. 

           

          All duties and taxes are the responsibility of the customer. 

          * Betafpv.com accepts no responsibilities and liabilities for delay in shipping time as this is beyond our control.

          Customer Reviews

          Based on 7 reviews Write a review